kwiaty 4

[ Pobierz całość w formacie PDF ]

Stem
Out at 7inat 2. the finished illustration as a
Out at 8inat 2. guide.
Working the thread from side to Petal outline.
Flower 3
side helps keep the thread flatter Shown on flower 3.
Leaf
at hole 2. Stitch the flower outline using
Stitch the other leaves in a the illustration as a guide.
similar way using the finished Stitch the other flowers in a
illustration as a guide. similar way using the finished
Leaf
Stems. illustration as a guide.
Green thread. Circles.
Work the stems in backstitch Gold thread.
Flower 4
using the illustration as a guide. Shown on circle 1.
Stem
Flowers. Out at Minat N.
Centre. Out at Oinat P.
Shown on flower 1. Out at Qinat R.
Leaf
Gold thread. Continue this sequence until
Leaf
Out at A in at B. circle 1 is complete.
Out at Cinat D. Stitch the other circles in a
Leaf
Out at Einat F. similar way to circle 1 using
Flower 5
Continue this sequence until the the finished illustration as a
centre is complete. guide.
Circle
Circle
Copyright � 2006 Stitching Cards
Bookmark Flower 6
Copyright � 2006 Stitching Cards
Bookmark Flower 6
152 mm
Copyright � 2006 Stitching Cards
104 mm
When printing the pricking pattern please set your printer scaling to "None" if available. If there is a "Fit to page" setting
on your printer settings then make sure this is not selected.
The page is based on an A4 sheet (210 x 297 mm) but should print on slightly different sized sheets correctly if the scaling
is set as suggested above.
The pattern size of 104 x 152 mm is given as a guide and may vary slightly on your printer. If it varies then centre the
pattern on your card as necessary.
Stitching Cards supports EveryChild, the international children's charity.
10% of the revenue from the sale of each pattern is donated to EveryChild.
Please encourage your friends to purchase official patterns from the Stitching Cards web site at www.stitchingcards.com.
Stitching Cards General Instructions
Published at www.stitchingcards.com
You will need a suitable pricking mat. This could be foam or felt but should allow easy penetration of
the pricking pin whilst protecting your work surface. Lay your blank card onto the pricking mat with the
right side (outside) of the card facing upwards.
Place the pricking pattern on the card in the required position. Use a fine pricking tool to pierce through
the pattern and the card. If you do not have a purpose made pricking tool then a hat pin or similar can be
used.
Remove the pricking pattern. The pricked holes can be seen on the card.
Turn the card over so the wrong side (inside) is uppermost.. Select a suitable thread such as Kreinik
metallic cord. Use a Number 10 embroidery needle. Use a length of thread that you are comfortable
with. We suggest using about a third of a metre (14 inches). Secure the end of the thread to the card with
adhesive tape. Pass the needle through the start hole from the back to the front of the card.
Follow the instruction diagram. Refer to the finished diagram from time to time to see the complete
stitching required.
When the thread on your needle runs out secure the end of the thread with adhesive tape on the back of
the card and start a new thread.
Continue to follow the instructions a section at a time. Some patterns uses beads. These are held in place
with stitching. You may need to use a beading needle if the bead holes are very fine.
If you are using a double fold card (a card with three panels) then place the completed card on your
work surface with the right side facing downwards. Fold the left-hand panel across to cover and hide the
back of the stitching work. Secure the panel in place with double-sided adhesive tape or card adhesive.
The stitching of your card is now complete. You may choose to add a suitable greeting with stickers,
stamping or handwriting.
Stitching Terminology.
Where the instructions say Out at this means passing the needle through a hole from the back of the
card to the front.
Where the instructions say In at this means passing the needle through a hole from the front of the
card to the back.
Where the design calls for back stitch this works as follows:
Out at 2inat 1
1 2 3 4
Out at 3inat 2
Out at 4inat 3
Where the design calls for stem stitch this works as follows:
Out at 1inat 3
1 3 4 5
2
Out at 2inat 4
Out at 3inat 5
Copyright � 2006 Stitching Cards
Web site www.stitchingcards.com
Stitching Cards, PO Box 795, St. Albans, AL2 2ZQ, UK [ Pobierz całość w formacie PDF ]

Podstrony